==== primer flasheo ====
(meto 71.3 en lugar de 81.3, no enciende)
<code>
Establishing Connection with Box in Main Mode...
Handling device: [Cyclone Team], [Cyclone Bootloader], [Platform: Classic]
Handling device: [Cyclone Team], [Cyclone Box], [Platform: Classic]
Initializing box...
Box Firmware: Cyclone Main Application v02.20, (Aug  6 2013 20:31:40, gcc v4.3.3, RTOS V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2012
Hardware Platform: Cyclone Classic Flasher Interface (c) 2008,2009 KarwosLabs
Box Serial Number: C000261F
HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2009, wk32
Initializing security card...
Card Serial Number: D70002D4
Card Firmware Revision: 0109
Card is activated
Box is activated
Started box selftests procedure
USB Voltage	4,96v	PASSED
MCU Voltage	3,30v	PASSED
Core Voltage	1,76v	PASSED
VBAT Voltage	0,01v	PASSED
VBAT Voltage	4,97v	PASSED
Box VPP disabled
VPP Voltage	0,02v	PASSED
Internal Box VPP Enabled
VPP Voltage	4,97v	PASSED
Box VPP disabled
VPP Voltage	0,02v	PASSED
External Box VPP Enabled
VPP Voltage	0,04v	FAILED - IGNORED - Probably power supply is not connected
Box VPP disabled
All box selftests passed!
Super DCT4 Activation: TRUE
XGold/Blackberry Service Running, Counter: 100
Lumia No TP is ACTIVATED!
Avaiable Physical Memory: 1.695GB
Avaiable Virtual Memory: 1.647GB
Avaiable Pagefile: 3.1023GB
Initializing FBUS...
All initialized - Ready to work
Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm530_071.004_prd.core.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_prd.core.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00020000-0x0003FFFF, ONENAND
EraseArea[0,CMT]: 0x00060000-0x004DFFFF, ONENAND
EraseArea[0,CMT]: 0x008E0000-0x0E77FFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 1.407s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT ADA Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT SOS+PMML Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT GENIO_INIT Certificate...
Writing CMT SOS*UPDAPP Certificate...
Writing CMT SOS*DSP0 Certificate...
Writing CMT LDSP Certificate...
Writing CMT SOS*ISASW Certificate...
Writing CMT SOS+CORE Certificate...
Writing CMT SOS+ROFS1 Certificate...
Programming Status OK!
All blocks written OK! Time taken 121.813s
Flashing Speed: 7407,74 kBit/S
Restarting MCU...
Processing rm530_071.004_prd.core.fpsx (APE)...
Processing rm530_071.004_01.01_Euro1_QW_prd.rofs2.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_01.01_Euro1_QW_prd.rofs2.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x07CC0000-0x0CDBFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.500s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS2 Certificate...
Programming Status OK!
All blocks written OK! Time taken 77.953s
Flashing Speed: 7492,03 kBit/S
Restarting MCU...
Processing rm530_071.004_01.01_Euro1_QW_prd.rofs2.fpsx (APE)...
Processing rm530_071.004_C00.01_DEFAULT_prd.rofs3.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_C00.01_DEFAULT_prd.rofs3.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0CDC0000-0x0E77FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.172s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS3 Certificate...
Programming Status OK!
All blocks written OK! Time taken 9.562s
Flashing Speed: 7395,40 kBit/S
Restarting MCU...
Processing rm530_071.004_C00.01_DEFAULT_prd.rofs3.fpsx (APE)...
Processing rm530_071.004_U007.000_prd.uda.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_U007.000_prd.uda.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0E780000-0x1F13FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 1.547s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 13.78s
Flashing Speed: 6542,74 kBit/S
Restarting MCU...
Processing rm530_071.004_U007.000_prd.uda.fpsx (APE)...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x004E0000-0x008DFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.62s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS*ENO Certificate...
Programming Status OK!
All blocks written OK! Time taken 3.31s
Flashing Speed: 7153,46 kBit/S
Restarting MCU...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (APE)...
All images processed OK! Processing post flash tasks...
Setting Factory Defaults...


CBUS Request Error -> CBUS Problem, Lost handle (Write Pipe)
CBUS Request Error -> CBUS Problem, Lost handle (Write Pipe)
Failed to disable VBAT -> No answer from CBUS
Factory defaults OK
Reading info...
CBUS Request Error -> CBUS Problem, Lost handle (Write Pipe)
CBUS Request Error -> CBUS Problem, Lost handle (Write Pipe)
Failed to disable VBAT -> No answer from CBUS
Failed to read info -> Phone not detected
Read info thread finished, continuing...
Post flash tasks finished!
Flashing successfully finished!
</code>

==== segundo flasheo ====
(meto 81.3 de otra zona y flasheo, todo correcto pero ingles y arabe)
especificamente, no he cambiado en product code, y el telefono enciende.
<code>
Establishing Connection with Box in Main Mode...
Handling device: [Cyclone Team], [Cyclone Bootloader], [Platform: Classic]
Handling device: [Cyclone Team], [Cyclone Box], [Platform: Classic]
Initializing box...
Box Firmware: Cyclone Main Application v02.20, (Aug  6 2013 20:31:40, gcc v4.3.3, RTOS V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2012
Hardware Platform: Cyclone Classic Flasher Interface (c) 2008,2009 KarwosLabs
Box Serial Number: C000261F
HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2009, wk32
Initializing security card...
Card Serial Number: D70002D4
Card Firmware Revision: 0109
Card is activated
Box is activated
Started box selftests procedure
USB Voltage	4,97v	PASSED
MCU Voltage	3,29v	PASSED
Core Voltage	1,76v	PASSED
VBAT Voltage	0,01v	PASSED
VBAT Voltage	4,96v	PASSED
Box VPP disabled
VPP Voltage	0,04v	PASSED
Internal Box VPP Enabled
VPP Voltage	4,92v	PASSED
Box VPP disabled
VPP Voltage	0,04v	PASSED
External Box VPP Enabled
VPP Voltage	0,04v	FAILED - IGNORED - Probably power supply is not connected
Box VPP disabled
All box selftests passed!
Super DCT4 Activation: TRUE
XGold/Blackberry Service Running, Counter: 100
Lumia No TP is ACTIVATED!
Avaiable Physical Memory: 1.1023GB
Avaiable Virtual Memory: 1.641GB
Avaiable Pagefile: 3.1023GB
Initializing FBUS...
All initialized - Ready to work
Failed to read info -> Phone not detected
Connecting to Cyclone Server...
Cyclone Server (2.0.0.117), Cyclone Box Team 2008-2013 - Ready.

[NaviFirm] Receiving Products List...
[NaviFirm] Receiving Variants List for RM-530 (Nokia E72)...
Connecting to Cyclone Server...
Cyclone Server (2.0.0.117), Cyclone Box Team 2008-2013 - Ready.

Failed to Read Product Code -> Phone not detected
Failed to Read Product Code -> Failed to Read Product Code
Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm530_081.003_prd.core.fpsx (CMT)...
Booting CMT...
Failed to Boot CMT -> CMT Not Responding, Phone or Cable problem
Processing Flash Image Failed -> Failed to Boot CMT
Failed to Process all Image files -> Failed to process rm530_081.003_prd.core.fpsx
Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm530_081.003_prd.core.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_prd.core.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00020000-0x0003FFFF, ONENAND
EraseArea[0,CMT]: 0x00060000-0x004DFFFF, ONENAND
EraseArea[0,CMT]: 0x008E0000-0x0E77FFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 1.375s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT ADA Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT SOS+PMML Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT GENIO_INIT Certificate...
Writing CMT SOS*UPDAPP Certificate...
Writing CMT SOS*DSP0 Certificate...
Writing CMT LDSP Certificate...
Writing CMT SOS*ISASW Certificate...
Writing CMT SOS+CORE Certificate...
Writing CMT SOS+ROFS1 Certificate...
Programming Status OK!
All blocks written OK! Time taken 123.31s
Flashing Speed: 7335,40 kBit/S
Restarting MCU...
Processing rm530_081.003_prd.core.fpsx (APE)...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x004E0000-0x008DFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.63s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS*ENO Certificate...
Programming Status OK!
All blocks written OK! Time taken 3.15s
Flashing Speed: 7191,42 kBit/S
Restarting MCU...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (APE)...
Processing rm530_081.003_32.01_MEA_C_QW2_prd.rofs2.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_32.01_MEA_C_QW2_prd.rofs2.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x07CC0000-0x0CDBFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.484s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS2 Certificate...
Programming Status OK!
All blocks written OK! Time taken 70.188s
Flashing Speed: 7435,59 kBit/S
Restarting MCU...
Processing rm530_081.003_32.01_MEA_C_QW2_prd.rofs2.fpsx (APE)...
Processing rm530_081.003_C00.01_DEFAULT_prd.rofs3.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_C00.01_DEFAULT_prd.rofs3.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0CDC0000-0x0E77FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.171s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS3 Certificate...
Programming Status OK!
All blocks written OK! Time taken 9.672s
Flashing Speed: 7311,29 kBit/S
Restarting MCU...
Processing rm530_081.003_C00.01_DEFAULT_prd.rofs3.fpsx (APE)...
Processing rm530_081.003_U010.000_prd.uda.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_U010.000_prd.uda.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0E780000-0x1F13FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 1.531s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 16.985s
Flashing Speed: 6743,30 kBit/S
Restarting MCU...
Processing rm530_081.003_U010.000_prd.uda.fpsx (APE)...
All images processed OK! Processing post flash tasks...
Setting Factory Defaults...
Factory defaults OK
Reading info...
MCU Version	V ICPR82_11w16.3.4
MCU Date	17-08-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
IMEI Spare	3A75980574830901
IMEI SV		3375980574830961F0000000
PSN		CEN820252
Product Code	0590447
Module Code	0204140
Basic Product Code	0583552
PSD		0000000000000000
LPSN		0
WLAN MAC	94007069379B
RETU		40
TAHVO		00
AHNE		11
HW		1001
RFIC		|Vapaus_5.1 | Mikki_1.1
DSP		ICPR82_11w16
Simlock Server	SIMLOCK SERVER
Simlock Key	2440700000000000
Simlock Profile	0000000000000000
Simlock Key Cnt	0
Simlock FBUS Cnt	0
Simlock [1,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [1,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [1,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [2,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [3,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [4,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [5,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [6,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [7,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Read info thread finished, continuing...
Post flash tasks finished!
Flashing successfully finished!
</code>

==== tercer flasheo ====
intento un downgrade con cyclone, a ver si cuela. El 81.3 no esta accesible :P

uso la 71.3, europea, black euro1
uso new downgrade. al empezar y al acabar tengo security ok

<code>
Establishing Connection with Box in Main Mode...
Handling device: [Cyclone Team], [Cyclone Bootloader], [Platform: Classic]
Handling device: [Cyclone Team], [Cyclone Box], [Platform: Classic]
Initializing box...
Box Firmware: Cyclone Main Application v02.20, (Aug  6 2013 20:31:40, gcc v4.3.3, RTOS V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2012
Hardware Platform: Cyclone Classic Flasher Interface (c) 2008,2009 KarwosLabs
Box Serial Number: C000261F
HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2009, wk32
Initializing security card...
Card Serial Number: D70002D4
Card Firmware Revision: 0109
Card is activated
Box is activated
Started box selftests procedure
USB Voltage	4,97v	PASSED
MCU Voltage	3,29v	PASSED
Core Voltage	1,76v	PASSED
VBAT Voltage	0,01v	PASSED
VBAT Voltage	4,96v	PASSED
Box VPP disabled
VPP Voltage	0,04v	PASSED
Internal Box VPP Enabled
VPP Voltage	4,92v	PASSED
Box VPP disabled
VPP Voltage	0,04v	PASSED
External Box VPP Enabled
VPP Voltage	0,04v	FAILED - IGNORED - Probably power supply is not connected
Box VPP disabled
All box selftests passed!
Super DCT4 Activation: TRUE
XGold/Blackberry Service Running, Counter: 100
Lumia No TP is ACTIVATED!
Avaiable Physical Memory: 1.1023GB
Avaiable Virtual Memory: 1.641GB
Avaiable Pagefile: 3.1023GB
Initializing FBUS...
All initialized - Ready to work
Failed to read info -> Phone not detected
Connecting to Cyclone Server...
Cyclone Server (2.0.0.117), Cyclone Box Team 2008-2013 - Ready.

[NaviFirm] Receiving Products List...
[NaviFirm] Receiving Variants List for RM-530 (Nokia E72)...
Connecting to Cyclone Server...
Cyclone Server (2.0.0.117), Cyclone Box Team 2008-2013 - Ready.

Failed to Read Product Code -> Phone not detected
Failed to Read Product Code -> Failed to Read Product Code
Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm530_081.003_prd.core.fpsx (CMT)...
Booting CMT...
Failed to Boot CMT -> CMT Not Responding, Phone or Cable problem
Processing Flash Image Failed -> Failed to Boot CMT
Failed to Process all Image files -> Failed to process rm530_081.003_prd.core.fpsx
Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm530_081.003_prd.core.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_prd.core.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00020000-0x0003FFFF, ONENAND
EraseArea[0,CMT]: 0x00060000-0x004DFFFF, ONENAND
EraseArea[0,CMT]: 0x008E0000-0x0E77FFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 1.375s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT ADA Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT SOS+PMML Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT GENIO_INIT Certificate...
Writing CMT SOS*UPDAPP Certificate...
Writing CMT SOS*DSP0 Certificate...
Writing CMT LDSP Certificate...
Writing CMT SOS*ISASW Certificate...
Writing CMT SOS+CORE Certificate...
Writing CMT SOS+ROFS1 Certificate...
Programming Status OK!
All blocks written OK! Time taken 123.31s
Flashing Speed: 7335,40 kBit/S
Restarting MCU...
Processing rm530_081.003_prd.core.fpsx (APE)...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x004E0000-0x008DFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.63s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS*ENO Certificate...
Programming Status OK!
All blocks written OK! Time taken 3.15s
Flashing Speed: 7191,42 kBit/S
Restarting MCU...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (APE)...
Processing rm530_081.003_32.01_MEA_C_QW2_prd.rofs2.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_32.01_MEA_C_QW2_prd.rofs2.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x07CC0000-0x0CDBFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.484s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS2 Certificate...
Programming Status OK!
All blocks written OK! Time taken 70.188s
Flashing Speed: 7435,59 kBit/S
Restarting MCU...
Processing rm530_081.003_32.01_MEA_C_QW2_prd.rofs2.fpsx (APE)...
Processing rm530_081.003_C00.01_DEFAULT_prd.rofs3.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_C00.01_DEFAULT_prd.rofs3.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0CDC0000-0x0E77FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.171s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS3 Certificate...
Programming Status OK!
All blocks written OK! Time taken 9.672s
Flashing Speed: 7311,29 kBit/S
Restarting MCU...
Processing rm530_081.003_C00.01_DEFAULT_prd.rofs3.fpsx (APE)...
Processing rm530_081.003_U010.000_prd.uda.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_U010.000_prd.uda.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0E780000-0x1F13FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 1.531s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 16.985s
Flashing Speed: 6743,30 kBit/S
Restarting MCU...
Processing rm530_081.003_U010.000_prd.uda.fpsx (APE)...
All images processed OK! Processing post flash tasks...
Setting Factory Defaults...
Factory defaults OK
Reading info...
MCU Version	V ICPR82_11w16.3.4
MCU Date	17-08-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
IMEI Spare	3A75980574830901
IMEI SV		3375980574830961F0000000
PSN		CEN820252
Product Code	0590447
Module Code	0204140
Basic Product Code	0583552
PSD		0000000000000000
LPSN		0
WLAN MAC	94007069379B
RETU		40
TAHVO		00
AHNE		11
HW		1001
RFIC		|Vapaus_5.1 | Mikki_1.1
DSP		ICPR82_11w16
Simlock Server	SIMLOCK SERVER
Simlock Key	2440700000000000
Simlock Profile	0000000000000000
Simlock Key Cnt	0
Simlock FBUS Cnt	0
Simlock [1,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [1,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [1,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [2,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [3,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [4,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [5,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [6,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [7,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Read info thread finished, continuing...
Post flash tasks finished!
Flashing successfully finished!
MCU Version	V ICPR82_11w16.3.4
MCU Date	17-08-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
IMEI Spare	3A75980574830901
IMEI SV		3375980574830961F0000000
PPM		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038
PSN		CEN820252
Product Code	0590447
Module Code	0204140
Basic Product Code	0583552
PSD		0000000000000000
LPSN		0
WLAN MAC	94007069379B
APE SW		081.003
APE Variant	081.003081.003.32.01081.003.C00.01
APE Test		v0.a038
APE HW		256
APE ADSP	256
APE BT		HCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.
RETU		40
TAHVO		00
AHNE		11
HW		1001o256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038
PCI		o256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01kv0.a038¥ rm530_081.003_U010.000_prd
UEM		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01kv0.a038¥ rm530_081.003_U010.000_prd
UPP		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038¥ rm530_081.003_U010.000_prd
RFIC		|Vapaus_5.1 | Mikki_1.1
DSP		ICPR82_11w16
LCD		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038¥ rm530_081.003_U010.000_prd
BT		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038
ADSP Sw		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038
ADSP DevID		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01kv0.a038¥ rm530_081.003_U010.000_prd
ADSP RevID		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01kv0.a038¥ rm530_081.003_U010.000_prd
AEM		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038¥ rm530_081.003_U010.000_prd
Flip MCUSW		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038¥ rm530_081.003_U010.000_prd
Simlock Server	SIMLOCK SERVER
Simlock Key	2440700000000000
Simlock Profile	0000000000000000
Simlock Key Cnt	0
Simlock FBUS Cnt	0
Simlock [1,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [1,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [1,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [2,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [3,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [4,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [5,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [6,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [7,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
MCU Version	V ICPR82_11w16.3.4
MCU Date	17-08-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
IMEI Spare	3A75980574830901
IMEI SV		3375980574830961F0000000
PPM		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038
PSN		CEN820252
Product Code	0590447
Module Code	0204140
Basic Product Code	0583552
PSD		0000000000000000
LPSN		0
WLAN MAC	94007069379B
APE SW		081.003
APE Variant	081.003081.003.32.01081.003.C00.01
APE Test		v0.a038
APE HW		256
APE ADSP	256
APE BT		HCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.
RETU		40
TAHVO		00
AHNE		11
HW		1001o256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038
PCI		o256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038
UEM		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01kv0.a038¥ rm530_081.003_U010.000_prd
UPP		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01kv0.a038¥ rm530_081.003_U010.000_prd
RFIC		|Vapaus_5.1 | Mikki_1.1o256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038¥ rm530_081.003_U010.000_prd
DSP		ICPR82_11w16o256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038¥ rm530_081.003_U010.000_prd
LCD		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01kv0.a038
BT		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01kv0.a038
ADSP Sw		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038
ADSP DevID		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038
ADSP RevID		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01kv0.a038¥ rm530_081.003_U010.000_prd
AEM		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01kv0.a038¥ rm530_081.003_U010.000_prd
Flip MCUSW		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i081.003j(#081.003081.003.32.01081.003.C00.01u, P>/kv0.a038¥ rm530_081.003_U010.000_prd
Simlock Server	SIMLOCK SERVER
Simlock Key	2440700000000000
Simlock Profile	0000000000000000
Simlock Key Cnt	0
Simlock FBUS Cnt	0
Simlock [1,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [1,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [1,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [2,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [3,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [4,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [5,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [6,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [7,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Step 1, Dumping Unique Data
"1260010CB9D70344B630E084C12C14C6403EC732.C000261F" Exists, That is good...
Step 2, Reading Full PM
Starting PM read in range 0-512...
[1] Reading 28 records
[1,0] Reading 114 bytes
[1,2] Reading 10 bytes
[1,4] Reading 110 bytes
[1,6] Reading 10 bytes
[1,7] Reading 214 bytes
[1,8] Reading 110 bytes
[1,13] Reading 10 bytes
[1,16] Reading 208 bytes
[1,18] Reading 208 bytes
[1,20] Reading 208 bytes
[1,22] Reading 16 bytes
[1,23] Reading 4 bytes
[1,24] Reading 84 bytes
[1,26] Reading 110 bytes
[1,28] Reading 10 bytes
[1,29] Reading 10 bytes
[1,31] Reading 208 bytes
[1,33] Reading 36 bytes
[1,34] Reading 376 bytes
[1,35] Reading 16 bytes
[1,37] Reading 4 bytes
[1,39] Reading 36 bytes
[1,40] Reading 16 bytes
[1,41] Reading 182 bytes
[1,42] Reading 4 bytes
[1,43] Reading 36 bytes
[1,44] Reading 182 bytes
[1,45] Reading 182 bytes
[2] Reading 1 records
[2,0] Reading 2080 bytes
[4] Reading 7 records
[4,1] Reading 1020 bytes
[4,3] Reading 10 bytes
[4,4] Reading 8 bytes
[4,5] Reading 8 bytes
[4,6] Reading 8 bytes
[4,9] Reading 5 bytes
[4,28] Reading 2 bytes
[8] Reading 6 records
[8,0] Reading 2 bytes
[8,1] Reading 16 bytes
[8,2] Reading 16 bytes
[8,3] Reading 128 bytes
[8,4] Reading 128 bytes
[8,8] Reading 8 bytes
[11] Reading 5 records
[11,0] Reading 4 bytes
[11,1] Reading 4 bytes
[11,2] Reading 4 bytes
[11,3] Reading 4 bytes
[11,4] Reading 1058 bytes
[12] Reading 1 records
[12,0] Reading 102 bytes
[31] Reading 1 records
[31,4] Reading 14 bytes
[44] Reading 1 records
[44,0] Reading 1 bytes
[50] Reading 1 records
[50,0] Reading 2 bytes
[54] Reading 2 records
[54,0] Reading 2 bytes
[54,2] Reading 24 bytes
[96] Reading 2 records
[96,0] Reading 2 bytes
[96,1] Reading 20 bytes
[107] Reading 6 records
[107,0] Reading 41 bytes
[107,1] Reading 89 bytes
[107,2] Reading 89 bytes
[107,3] Reading 70 bytes
[107,25] Reading 236 bytes
[107,26] Reading 12 bytes
[117] Reading 3 records
[117,5] Reading 10 bytes
[117,6] Reading 8 bytes
[117,8] Reading 42 bytes
[120] Reading 4 records
[120,0] Reading 944 bytes
[120,1] Reading 160 bytes
[120,2] Reading 130 bytes
[120,3] Reading 112 bytes
[153] Reading 7 records
[153,0] Reading 68 bytes
[153,1] Reading 68 bytes
[153,2] Reading 68 bytes
[153,3] Reading 68 bytes
[153,4] Reading 68 bytes
[153,5] Reading 68 bytes
[153,6] Reading 68 bytes
[193] Reading 4 records
[193,2] Reading 8 bytes
[193,3] Reading 32 bytes
[193,4] Reading 32 bytes
[193,9] Reading 64 bytes
[217] Reading 1 records
[217,0] Reading 32 bytes
[239] Reading 3 records
[239,0] Reading 2 bytes
[239,1] Reading 3284 bytes
[239,6] Reading 218 bytes
[291] Reading 1 records
[291,0] Reading 92 bytes
[308] Reading 7 records
[308,0] Reading 1 bytes
[308,1] Reading 8192 bytes
[308,3] Reading 1 bytes
[308,4] Reading 1 bytes
[308,6] Reading 1 bytes
[308,7] Reading 1 bytes
[308,9] Reading 40 bytes
[309] Reading 7 records
[309,0] Reading 4 bytes
[309,1] Reading 2 bytes
[309,2] Reading 12 bytes
[309,3] Reading 36 bytes
[309,4] Reading 12 bytes
[309,7] Reading 12 bytes
[309,17] Reading 12 bytes
[313] Reading 1 records
[313,0] Reading 173 bytes
[322] Reading 1 records
[322,0] Reading 1 bytes
[329] Reading 1 records
[329,0] Reading 8392 bytes
[334] Reading 1 records
[334,0] Reading 1 bytes
[341] Reading 3 records
[341,0] Reading 1 bytes
[341,3] Reading 4 bytes
[341,4] Reading 4390 bytes
[354] Reading 1 records
[354,0] Reading 15 bytes
[356] Reading 2 records
[356,0] Reading 2 bytes
[356,1] Reading 8 bytes
[360] Reading 3 records
[360,0] Reading 1 bytes
[360,1] Reading 2 bytes
[360,2] Reading 3 bytes
[369] Reading 1 records
[369,0] Reading 40 bytes
PM Read OK, Time taken 15.47s
Step 3, Dumping RPL
RPL Creation started...
Processing CMT Part...
Storing Product Code...
Storing PSN...
Storing HWID...
Trying to store Simlock...
Reading Configuration Key...
Hashing...
Reading SHA1-RSA Signature...
Reading SHA1-HMAC Signature...
Storing Simlock...
Trying to store WMDRM RPL...
Reading Keys...
Storing WMDRM PD...
Reading Security Block...
Security block OK and saved to "RM-530_357895047389012_15042019_150400.SecurityBlock.PM"
"1260010CB9D70344B630E084C12C14C6403EC732.C000261F" Exists, That is good...
Storing Additional Data...
Checking Superdongle Key...
Encrypting Superdongle Key...
Storing Superdongle Key...
Checking CMLA Key...
Storing CMLA Key...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Storing NPC...
Storing CCC...
Storing HWC...
CMT VARIANT Not Found
Storing PARTNERC...
Restarting MCU...
RPL Saved OK
Step 4, Full Erase
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Erasing flash chip...
Started group flash erase
EraseArea[0,CMT]: 0x00000000-0x1FFFFFFF, ONENAND
Waiting 640s for erasure finish...
Erase taken 2.875s
Restarting MCU...
BB5 Full Erase Finished!
Step 4, Full Flash
Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm530_071.004_prd.core.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_prd.core.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0xFFFFFFFF00000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
Warning: PAPUBKEYS Hash Missing!
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00020000-0x0003FFFF, ONENAND
EraseArea[0,CMT]: 0x00060000-0x004DFFFF, ONENAND
EraseArea[0,CMT]: 0x008E0000-0x0E77FFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 1.390s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT ADA Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT SOS+PMML Certificate...
Writing CMT PASUBTOC Certificate...
WARNING: CMT PAPUBKEYS Hash is Empty, writing first found PAPUBKEYS
Writing CMT PAPUBKEYS Certificate...
Writing CMT GENIO_INIT Certificate...
Writing CMT SOS*UPDAPP Certificate...
Writing CMT SOS*DSP0 Certificate...
Writing CMT LDSP Certificate...
Writing CMT SOS*ISASW Certificate...
Writing CMT SOS+CORE Certificate...
Writing CMT SOS+ROFS1 Certificate...
Programming Status OK!
All blocks written OK! Time taken 121.547s
Flashing Speed: 7423,95 kBit/S
Restarting MCU...
Processing rm530_071.004_prd.core.fpsx (APE)...
Processing rm530_071.004_01.01_Euro1_QW_prd.rofs2.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_01.01_Euro1_QW_prd.rofs2.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x07CC0000-0x0CDBFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.485s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS2 Certificate...
Programming Status OK!
All blocks written OK! Time taken 77.875s
Flashing Speed: 7499,53 kBit/S
Restarting MCU...
Processing rm530_071.004_01.01_Euro1_QW_prd.rofs2.fpsx (APE)...
Processing rm530_071.004_C00.01_DEFAULT_prd.rofs3.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_C00.01_DEFAULT_prd.rofs3.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0CDC0000-0x0E77FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.187s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS3 Certificate...
Programming Status OK!
All blocks written OK! Time taken 9.546s
Flashing Speed: 7407,80 kBit/S
Restarting MCU...
Processing rm530_071.004_C00.01_DEFAULT_prd.rofs3.fpsx (APE)...
Processing rm530_071.004_U007.000_prd.uda.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_U007.000_prd.uda.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0E780000-0x1F13FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 1.531s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 13.78s
Flashing Speed: 6542,74 kBit/S
Restarting MCU...
Processing rm530_071.004_U007.000_prd.uda.fpsx (APE)...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x004E0000-0x008DFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.47s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS*ENO Certificate...
Programming Status OK!
All blocks written OK! Time taken 3.15s
Flashing Speed: 7191,42 kBit/S
Restarting MCU...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (APE)...
All images processed OK! Processing post flash tasks...
Setting Factory Defaults...
Factory defaults OK
Reading info...
MCU Version	V ICPR82_11w16.3
MCU Date	19-05-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		12345610654321?
IMEI Spare	1A32541660452301
IMEI SV		1332541660452351F8000000
PSN		0
PSD		0000000000000000
LPSN		0
RETU		40
TAHVO		00
AHNE		11
RFIC		|Vapaus_5.1 | Mikki_1.1
DSP		ICPR82_11w16
Failed to read info -> Failed to read SP info
Read info thread finished, continuing...
Post flash tasks finished!
Flashing successfully finished!
Step 5, RPL Write
Skipping RPL decryption...
Parsing decrypted RPL...
Processing FBUS Part...
Writing Product Code... 
Writing PSN... 
Writing HWID... 
Writing Simlock...
Handling as SL3 Simlock Data
Handling as SIMLOCK1 Format
Reading Security Block...
Security block OK and saved to "RM-530_12345610654321_15042019_150848.SecurityBlock.PM"
15 Digits NCK Found
Simlock ACCEPTED OK !
Writing Superdongle key...
Failed to Write RPL File -> Phone is not responding for Superdongle Request
Failed to Proceed with New Downgrade -> Failed to Write RPL
MCU Version	V ICPR82_11w16.3
MCU Date	19-05-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		12345610654321?
IMEI Spare	1A32541660452301
IMEI SV		1332541660452351F8000000
PPM		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01u, P>/kv0.a038
PSN		CEN820252
Product Code	0590447
PSD		0000000000000000
LPSN		0
APE SW		071.004
APE Variant	071.004071.004.01.01071.004.C00.01
APE Test		v0.a038
APE HW		256
APE ADSP	256
APE BT		HCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.
RETU		40
TAHVO		00
AHNE		11
HW		1001o256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01u, P>/kv0.a038
PCI		o256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01kv0.a038¥ rm530_071.004_U007.000_prd
UEM		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01kv0.a038¥ rm530_071.004_U007.000_prd
UPP		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01u, P>/kv0.a038¥ rm530_071.004_U007.000_prd
RFIC		|Vapaus_5.1 | Mikki_1.1
DSP		ICPR82_11w16
LCD		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01u, P>/kv0.a038¥ rm530_071.004_U007.000_prd
BT		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01u, P>/kv0.a038
ADSP Sw		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01u, P>/kv0.a038
ADSP DevID		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01kv0.a038¥ rm530_071.004_U007.000_prd
ADSP RevID		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01kv0.a038¥ rm530_071.004_U007.000_prd
AEM		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01u, P>/kv0.a038¥ rm530_071.004_U007.000_prd
Flip MCUSW		256qPIHCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.n256i071.004j(#071.004071.004.01.01071.004.C00.01u, P>/kv0.a038¥ rm530_071.004_U007.000_prd
Failed to read info -> Failed to read SP info
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
APE Boot skipped on user request
Flashbus Write baud set to 5.0Mbits
Failed to BB5 Downgrade Repair -> Invalid NPC Found! Magic is BAD!
Started IMEI Recovery...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Looking NPC for 1260010CB9D70344B630E084C12C14C6403EC732...
Failed to Recovery IMEI -> Range check error
Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm530_081.003_prd.core.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_prd.core.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00020000-0x0003FFFF, ONENAND
EraseArea[0,CMT]: 0x00060000-0x004DFFFF, ONENAND
EraseArea[0,CMT]: 0x008E0000-0x0E77FFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 1.359s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT ADA Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT SOS+PMML Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT GENIO_INIT Certificate...
Writing CMT SOS*UPDAPP Certificate...
Writing CMT SOS*DSP0 Certificate...
Writing CMT LDSP Certificate...
Writing CMT SOS*ISASW Certificate...
Writing CMT SOS+CORE Certificate...
Writing CMT SOS+ROFS1 Certificate...
Programming Status OK!
All blocks written OK! Time taken 121.500s
Flashing Speed: 7427,83 kBit/S
Restarting MCU...
Processing rm530_081.003_prd.core.fpsx (APE)...
Processing rm530_081.003_32.01_MEA_C_QW2_prd.rofs2.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_32.01_MEA_C_QW2_prd.rofs2.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x07CC0000-0x0CDBFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.500s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS2 Certificate...
Programming Status OK!
All blocks written OK! Time taken 69.844s
Flashing Speed: 7472,21 kBit/S
Restarting MCU...
Processing rm530_081.003_32.01_MEA_C_QW2_prd.rofs2.fpsx (APE)...
Processing rm530_081.003_C00.01_DEFAULT_prd.rofs3.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_C00.01_DEFAULT_prd.rofs3.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0CDC0000-0x0E77FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.172s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS3 Certificate...
Programming Status OK!
All blocks written OK! Time taken 9.609s
Flashing Speed: 7359,23 kBit/S
Restarting MCU...
Processing rm530_081.003_C00.01_DEFAULT_prd.rofs3.fpsx (APE)...
Processing rm530_081.003_U010.000_prd.uda.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_081.003_U010.000_prd.uda.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0E780000-0x1F13FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 1.547s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 16.844s
Flashing Speed: 6799,75 kBit/S
Restarting MCU...
Processing rm530_081.003_U010.000_prd.uda.fpsx (APE)...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x004E0000-0x008DFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.46s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS*ENO Certificate...
Programming Status OK!
All blocks written OK! Time taken 3.31s
Flashing Speed: 7153,46 kBit/S
Restarting MCU...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (APE)...
All images processed OK! Processing post flash tasks...
Setting Factory Defaults...
Factory defaults OK
Reading info...
MCU Version	V ICPR82_11w16.3.4
MCU Date	17-08-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		12345610654321?
IMEI Spare	1A32541660452301
IMEI SV		1332541660452361F0000000
PSN		CEN820252
Product Code	0590447
PSD		0000000000000000
LPSN		0
RETU		40
TAHVO		00
AHNE		11
HW		1001
RFIC		|Vapaus_5.1 | Mikki_1.1
DSP		ICPR82_11w16
Failed to read info -> Failed to read SP info
Read info thread finished, continuing...
Post flash tasks finished!
Flashing successfully finished!
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
APE Boot skipped on user request
Flashbus Write baud set to 5.0Mbits
Failed to BB5 Downgrade Repair -> Invalid NPC Found! Magic is BAD!
SX4 Authorization / SD Repair Procedure Started....
Failed to Authorize SX4 -> Phone not detected
Skipping RPL decryption...
Parsing decrypted RPL...
Processing FBUS Part...
Writing Product Code... 
Writing PSN... 
Writing HWID... 
Writing Simlock...
Handling as SL3 Simlock Data
Handling as SIMLOCK1 Format
Reading Security Block...
Security block OK and saved to "RM-530_12345610654321_15042019_152315.SecurityBlock.PM"
15 Digits NCK Found
Simlock ACCEPTED OK !
Writing Superdongle key...
Superdongle Key ACCEPTED OK !
Writing CMLA key...
CMLA Key ACCEPTED OK !
Writing WMDRM PD Data...
WMDRM PD Data ACCEPTED OK !
Processing FLASHBUS Part...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
CMT NPC Erased
CMT NPC Written
CMT HWC Erased
CMT HWC Written
CMT CCC Erased
CMT CCC Written
CMT PARTNERC Erased
CMT PARTNERC Written
Restarting MCU...
Write RPL Finished!
Started Phone Security Analysis...
MCU Version	V ICPR82_11w16.3.4
MCU Date	17-08-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
Reading Security Block...
Security block OK and saved to "RM-530_357895047389012_15042019_152533.SecurityBlock.PM"
Step 1 : Testing SIMLOCK
SIMLOCK SEFLTEST PASSED OK!
Step 2 : Testing SECURITY
-- SECURITY PROBLEM --

Phone have failed SECURITY Test, that means Superdongle Area is DAMAGED!
To repair it, simply slick "SX4 Authorization / SD Repair" button.
After SX4/SD Repair, don't forget to write PM file with fields 1,309 (if SW don't do this automatically)

Additionaly, Checking HWC/CCC Certs...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
HWC Looks OK!
CCC Looks OK!
Restarting MCU...
-- SECURITY PROBLEM --
Step 3 : Analyzing Security Block
"1260010CB9D70344B630E084C12C14C6403EC732.C000261F" Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking ECC KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking DIV KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Analyze finished!
SX4 Authorization / SD Repair Procedure Started....
"1260010CB9D70344B630E084C12C14C6403EC732.C000261F" Exists, That is good...
MCU Version	V ICPR82_11w16.3.4
MCU Date	17-08-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
Reading Security Block...
Security block OK and saved to "RM-530_357895047389012_15042019_152612.SecurityBlock.PM"
SX4 Status: Not authorized (74)
Started mutual authenthication with card...
Receiving Phone Seed 1...
Phone Seed 1 Received
Sending calculated Data 1, and expecting Seed 2...
Calculated Data 1 accepted, Phone Seed 2 Received
Sending calculated Data 2
Calculated Data 2 sent, Checking Authorization Status again
Authorization successfully finished!
Looking for Virgin PM In Database...
Found, but writing canceled by user
MCU Version	V ICPR82_11w16.3.4
MCU Date	17-08-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
IMEI Spare	3A75980574830901
IMEI SV		3375980574830961F0000000
PSN		CEN820252
Product Code	0590447
PSD		0000000000000000
LPSN		0
WLAN MAC	94007069379B
APE SW		081.003
APE Variant	081.003081.003.32.01081.003.C00.01
APE Test		v0.a038
APE HW		256
APE ADSP	256
RETU		40
TAHVO		00
AHNE		11
HW		1001
RFIC		|Vapaus_5.1 | Mikki_1.1
DSP		ICPR82_11w16
Simlock Server	SIMLOCK SERVER
Simlock Key	2440700000000000
Simlock Profile	0000000000000000
Simlock Key Cnt	0
Simlock FBUS Cnt	0
Simlock [1,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [1,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [1,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [2,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [3,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [4,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [5,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [6,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [7,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Started Phone Security Analysis...
MCU Version	V ICPR82_11w16.3.4
MCU Date	17-08-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
Reading Security Block...
Security block OK and saved to "RM-530_357895047389012_15042019_153208.SecurityBlock.PM"
Step 1 : Testing SIMLOCK
SIMLOCK SEFLTEST PASSED OK!
Step 2 : Testing SECURITY
-- SECURITY PROBLEM --

Phone have failed SECURITY Test, that means Superdongle Area is DAMAGED!
To repair it, simply slick "SX4 Authorization / SD Repair" button.
After SX4/SD Repair, don't forget to write PM file with fields 1,309 (if SW don't do this automatically)

Additionaly, Checking HWC/CCC Certs...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
HWC Looks OK!
CCC Looks OK!
Restarting MCU...
-- SECURITY PROBLEM --
Step 3 : Analyzing Security Block
"1260010CB9D70344B630E084C12C14C6403EC732.C000261F" Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking ECC KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking DIV KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Analyze finished!
SX4 Authorization / SD Repair Procedure Started....
"1260010CB9D70344B630E084C12C14C6403EC732.C000261F" Exists, That is good...
MCU Version	V ICPR82_11w16.3.4
MCU Date	17-08-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
Reading Security Block...
Security block OK and saved to "RM-530_357895047389012_15042019_153549.SecurityBlock.PM"
SX4 Status: Not authorized (74)
Started mutual authenthication with card...
Receiving Phone Seed 1...
Phone Seed 1 Received
Sending calculated Data 1, and expecting Seed 2...
Calculated Data 1 accepted, Phone Seed 2 Received
Sending calculated Data 2
Calculated Data 2 sent, Checking Authorization Status again
Authorization successfully finished!
Looking for Virgin PM In Database...
Found, writing...
[1,0] Written, Length: 114 bytes, Status: OK
[1,2] Written, Length: 10 bytes, Status: OK
[1,4] Written, Length: 110 bytes, Status: OK
[1,6] Written, Length: 10 bytes, Status: OK
[1,7] Written, Length: 214 bytes, Status: OK
[1,8] Written, Length: 110 bytes, Status: OK
[1,13] Written, Length: 10 bytes, Status: OK
[1,16] Written, Length: 208 bytes, Status: OK
[1,18] Written, Length: 208 bytes, Status: OK
[1,20] Written, Length: 208 bytes, Status: OK
[1,22] Written, Length: 16 bytes, Status: OK
[1,23] Written, Length: 4 bytes, Status: OK
[1,24] Written, Length: 84 bytes, Status: OK
[1,26] Written, Length: 110 bytes, Status: OK
[1,28] Written, Length: 10 bytes, Status: OK
[1,29] Written, Length: 10 bytes, Status: OK
[1,31] Written, Length: 208 bytes, Status: OK
[1,33] Written, Length: 36 bytes, Status: OK
[1,34] Written, Length: 376 bytes, Status: OK
[1,35] Written, Length: 16 bytes, Status: OK
[1,37] Written, Length: 4 bytes, Status: OK
[1,39] Written, Length: 36 bytes, Status: OK
[1,40] Written, Length: 16 bytes, Status: OK
[1,41] Written, Length: 182 bytes, Status: OK
[1,42] Written, Length: 4 bytes, Status: OK
[1,43] Written, Length: 36 bytes, Status: OK
[1,44] Written, Length: 182 bytes, Status: OK
[1,45] Written, Length: 182 bytes, Status: OK
[309,0] Written, Length: 4 bytes, Status: OK
[309,1] Written, Length: 2 bytes, Status: OK
[309,2] Written, Length: 12 bytes, Status: OK
[309,3] Written, Length: 36 bytes, Status: OK
[309,4] Written, Length: 12 bytes, Status: OK
[309,7] Written, Length: 12 bytes, Status: OK
[309,17] Written, Length: 12 bytes, Status: OK
Write PM Finished, Record written OK: 35, Record written NOT OK: 0
Started Phone Security Analysis...
MCU Version	V ICPR82_11w16.3.4
MCU Date	17-08-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
Reading Security Block...
Security block OK and saved to "RM-530_357895047389012_15042019_153602.SecurityBlock.PM"
Step 1 : Testing SIMLOCK
SIMLOCK SEFLTEST PASSED OK!
Step 2 : Testing SECURITY
SECURITY SEFLTEST PASSED OK!
Step 3 : Analyzing Security Block
"1260010CB9D70344B630E084C12C14C6403EC732.C000261F" Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking ECC KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking DIV KEYS...
DIV KEYS FOUND AND CHECKSUM OK! PASSED!
Analyze finished!
Step 1, Dumping Unique Data
"1260010CB9D70344B630E084C12C14C6403EC732.C000261F" Exists, That is good...
Step 2, Reading Full PM
Starting PM read in range 0-512...
[1] Reading 28 records
[1,0] Reading 114 bytes
[1,2] Reading 10 bytes
[1,4] Reading 110 bytes
[1,6] Reading 10 bytes
[1,7] Reading 214 bytes
[1,8] Reading 110 bytes
[1,13] Reading 10 bytes
[1,16] Reading 208 bytes
[1,18] Reading 208 bytes
[1,20] Reading 208 bytes
[1,22] Reading 16 bytes
[1,23] Reading 4 bytes
[1,24] Reading 84 bytes
[1,26] Reading 110 bytes
[1,28] Reading 10 bytes
[1,29] Reading 10 bytes
[1,31] Reading 208 bytes
[1,33] Reading 36 bytes
[1,34] Reading 376 bytes
[1,35] Reading 16 bytes
[1,37] Reading 4 bytes
[1,39] Reading 36 bytes
[1,40] Reading 16 bytes
[1,41] Reading 182 bytes
[1,42] Reading 4 bytes
[1,43] Reading 36 bytes
[1,44] Reading 182 bytes
[1,45] Reading 182 bytes
[2] Reading 1 records
[2,0] Reading 2080 bytes
[4] Reading 3 records
[4,3] Reading 10 bytes
[4,4] Reading 8 bytes
[4,9] Reading 5 bytes
[8] Reading 5 records
[8,0] Reading 2 bytes
[8,3] Reading 128 bytes
[8,4] Reading 128 bytes
[8,8] Reading 8 bytes
[8,10] Reading 32 bytes
[11] Reading 5 records
[11,0] Reading 4 bytes
[11,1] Reading 4 bytes
[11,2] Reading 4 bytes
[11,3] Reading 4 bytes
[11,4] Reading 1058 bytes
[12] Reading 1 records
[12,0] Reading 102 bytes
[26] Reading 2 records
[26,0] Reading 16 bytes
[26,1] Reading 68 bytes
[31] Reading 1 records
[31,4] Reading 14 bytes
[44] Reading 1 records
[44,0] Reading 1 bytes
[50] Reading 1 records
[50,0] Reading 2 bytes
[54] Reading 1 records
[54,0] Reading 2 bytes
[96] Reading 1 records
[96,0] Reading 2 bytes
[107] Reading 6 records
[107,0] Reading 41 bytes
[107,1] Reading 89 bytes
[107,2] Reading 89 bytes
[107,3] Reading 70 bytes
[107,25] Reading 236 bytes
[107,26] Reading 12 bytes
[120] Reading 4 records
[120,0] Reading 944 bytes
[120,1] Reading 160 bytes
[120,2] Reading 130 bytes
[120,3] Reading 112 bytes
[153] Reading 7 records
[153,0] Reading 68 bytes
[153,1] Reading 68 bytes
[153,2] Reading 68 bytes
[153,3] Reading 68 bytes
[153,4] Reading 68 bytes
[153,5] Reading 68 bytes
[153,6] Reading 68 bytes
[193] Reading 4 records
[193,2] Reading 8 bytes
[193,3] Reading 32 bytes
[193,4] Reading 32 bytes
[193,9] Reading 64 bytes
[217] Reading 1 records
[217,0] Reading 32 bytes
[239] Reading 1 records
[239,6] Reading 218 bytes
[291] Reading 1 records
[291,0] Reading 92 bytes
[308] Reading 8 records
[308,0] Reading 1 bytes
[308,1] Reading 8192 bytes
[308,2] Reading 1 bytes
[308,3] Reading 1 bytes
[308,4] Reading 1 bytes
[308,6] Reading 1 bytes
[308,7] Reading 1 bytes
[308,9] Reading 40 bytes
[309] Reading 7 records
[309,0] Reading 4 bytes
[309,1] Reading 2 bytes
[309,2] Reading 12 bytes
[309,3] Reading 36 bytes
[309,4] Reading 12 bytes
[309,7] Reading 12 bytes
[309,17] Reading 12 bytes
[322] Reading 1 records
[322,0] Reading 1 bytes
[329] Reading 1 records
[329,0] Reading 8392 bytes
[334] Reading 1 records
[334,0] Reading 1 bytes
[341] Reading 1 records
[341,0] Reading 1 bytes
[354] Reading 1 records
[354,0] Reading 13 bytes
[356] Reading 1 records
[356,0] Reading 2 bytes
[360] Reading 2 records
[360,0] Reading 1 bytes
[360,1] Reading 2 bytes
[369] Reading 1 records
[369,0] Reading 40 bytes
PM Read OK, Time taken 13.812s
Step 3, Dumping RPL
RPL Creation started...
Processing CMT Part...
Storing Product Code...
Storing PSN...
Storing HWID...
Trying to store Simlock...
Reading Configuration Key...
Hashing...
Reading SHA1-RSA Signature...
Reading SHA1-HMAC Signature...
Storing Simlock...
Trying to store WMDRM RPL...
Reading Keys...
Failed to read WMDRM Key
Reading Security Block...
Security block OK and saved to "RM-530_357895047389012_15042019_153710.SecurityBlock.PM"
"1260010CB9D70344B630E084C12C14C6403EC732.C000261F" Exists, That is good...
Storing Additional Data...
Checking Superdongle Key...
Encrypting Superdongle Key...
Storing Superdongle Key...
Checking CMLA Key...
CMLA Key Store Problem -> Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Storing NPC...
Storing CCC...
Storing HWC...
CMT VARIANT Not Found
Storing PARTNERC...
Restarting MCU...
RPL Saved OK
Step 4, Full Erase
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Erasing flash chip...
Started group flash erase
EraseArea[0,CMT]: 0x00000000-0x1FFFFFFF, ONENAND
Waiting 640s for erasure finish...
Erase taken 2.875s
Restarting MCU...
BB5 Full Erase Finished!
Step 4, Full Flash
Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm530_071.004_prd.core.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_prd.core.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0xFFFFFFFF00000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
Warning: PAPUBKEYS Hash Missing!
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00020000-0x0003FFFF, ONENAND
EraseArea[0,CMT]: 0x00060000-0x004DFFFF, ONENAND
EraseArea[0,CMT]: 0x008E0000-0x0E77FFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 1.406s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT ADA Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT SOS+PMML Certificate...
Writing CMT PASUBTOC Certificate...
WARNING: CMT PAPUBKEYS Hash is Empty, writing first found PAPUBKEYS
Writing CMT PAPUBKEYS Certificate...
Writing CMT GENIO_INIT Certificate...
Writing CMT SOS*UPDAPP Certificate...
Writing CMT SOS*DSP0 Certificate...
Writing CMT LDSP Certificate...
Writing CMT SOS*ISASW Certificate...
Writing CMT SOS+CORE Certificate...
Writing CMT SOS+ROFS1 Certificate...
Programming Status OK!
All blocks written OK! Time taken 121.562s
Flashing Speed: 7423,03 kBit/S
Restarting MCU...
Processing rm530_071.004_prd.core.fpsx (APE)...
Processing rm530_071.004_01.01_Euro1_QW_prd.rofs2.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_01.01_Euro1_QW_prd.rofs2.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x07CC0000-0x0CDBFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.484s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS2 Certificate...
Programming Status OK!
All blocks written OK! Time taken 77.844s
Flashing Speed: 7502,52 kBit/S
Restarting MCU...
Processing rm530_071.004_01.01_Euro1_QW_prd.rofs2.fpsx (APE)...
Processing rm530_071.004_C00.01_DEFAULT_prd.rofs3.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_C00.01_DEFAULT_prd.rofs3.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0CDC0000-0x0E77FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.172s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS3 Certificate...
Programming Status OK!
All blocks written OK! Time taken 9.562s
Flashing Speed: 7395,40 kBit/S
Restarting MCU...
Processing rm530_071.004_C00.01_DEFAULT_prd.rofs3.fpsx (APE)...
Processing rm530_071.004_U007.000_prd.uda.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
rm530_071.004_U007.000_prd.uda.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x0E780000-0x1F13FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 1.547s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 13.79s
Flashing Speed: 6542,24 kBit/S
Restarting MCU...
Processing rm530_071.004_U007.000_prd.uda.fpsx (APE)...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x004E0000-0x008DFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.47s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS*ENO Certificate...
Programming Status OK!
All blocks written OK! Time taken 3.15s
Flashing Speed: 7191,42 kBit/S
Restarting MCU...
Processing RM530_ENO_APE_ONLY_09wk35_v0.038.fpsx (APE)...
All images processed OK! Processing post flash tasks...
Setting Factory Defaults...
Factory defaults OK
Reading info...
MCU Version	V ICPR82_11w16.3
MCU Date	19-05-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		12345610654321?
IMEI Spare	1A32541660452301
IMEI SV		1332541660452351F8000000
PSN		0
PSD		0000000000000000
LPSN		0
RETU		40
TAHVO		00
AHNE		11
RFIC		|Vapaus_5.1 | Mikki_1.1
DSP		ICPR82_11w16
Failed to read info -> Failed to read SP info
Read info thread finished, continuing...
Post flash tasks finished!
Flashing successfully finished!
Step 5, RPL Write
Skipping RPL decryption...
Parsing decrypted RPL...
Processing FBUS Part...
Writing Product Code... 
Writing PSN... 
Writing HWID... 
Writing Simlock...
Handling as SL3 Simlock Data
Handling as SIMLOCK1 Format
Reading Security Block...
Security block OK and saved to "RM-530_12345610654321_15042019_154244.SecurityBlock.PM"
15 Digits NCK Found
Simlock ACCEPTED OK !
Writing Superdongle key...
Superdongle Key ACCEPTED OK !
Processing FLASHBUS Part...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000030000022600010007600C192102011104
CMT_EM_ASIC_ID:		00001040
CMT_EM_ASIC_ID:		00001030
CMT_PUBLIC_ID:		1260010CB9D70344B630E084C12C14C6403EC732
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC:	3E273BF6
CMT_SECURE_ROM_CRC:	37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000031, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 660D81A4455F6F7F9B81D5D10F5336B14B50635E
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
CMT NPC Erased
CMT NPC Written
CMT HWC Erased
CMT HWC Written
CMT CCC Erased
CMT CCC Written
CMT PARTNERC Erased
CMT PARTNERC Written
Restarting MCU...
Write RPL Finished!
Step 6, SX4 Authorization + PM Write
SX4 Authorization / SD Repair Procedure Started....
"1260010CB9D70344B630E084C12C14C6403EC732.C000261F" Exists, That is good...
MCU Version	V ICPR82_11w16.3
MCU Date	19-05-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
Reading Security Block...
Security block OK and saved to "RM-530_357895047389012_15042019_154259.SecurityBlock.PM"
SX4 Status: Not authorized (74)
Started mutual authenthication with card...
Receiving Phone Seed 1...
Phone Seed 1 Received
Sending calculated Data 1, and expecting Seed 2...
Calculated Data 1 accepted, Phone Seed 2 Received
Sending calculated Data 2
Calculated Data 2 sent, Checking Authorization Status again
Authorization successfully finished!
Looking for Virgin PM In Database...
Writing PM...
[1,0] Written, Length: 114 bytes, Status: OK
[1,2] Written, Length: 10 bytes, Status: OK
[1,4] Written, Length: 110 bytes, Status: OK
[1,6] Written, Length: 10 bytes, Status: OK
[1,7] Written, Length: 214 bytes, Status: OK
[1,8] Written, Length: 110 bytes, Status: OK
[1,13] Written, Length: 10 bytes, Status: OK
[1,16] Written, Length: 208 bytes, Status: OK
[1,18] Written, Length: 208 bytes, Status: OK
[1,20] Written, Length: 208 bytes, Status: OK
[1,22] Written, Length: 16 bytes, Status: OK
[1,23] Written, Length: 4 bytes, Status: OK
[1,24] Written, Length: 84 bytes, Status: OK
[1,26] Written, Length: 110 bytes, Status: OK
[1,28] Written, Length: 10 bytes, Status: OK
[1,29] Written, Length: 10 bytes, Status: OK
[1,31] Written, Length: 208 bytes, Status: OK
[1,33] Written, Length: 36 bytes, Status: OK
[1,34] Written, Length: 376 bytes, Status: OK
[1,35] Written, Length: 16 bytes, Status: OK
[1,37] Written, Length: 4 bytes, Status: OK
[1,39] Written, Length: 36 bytes, Status: OK
[1,40] Written, Length: 16 bytes, Status: OK
[1,41] Written, Length: 182 bytes, Status: OK
[1,42] Written, Length: 4 bytes, Status: OK
[1,43] Written, Length: 36 bytes, Status: OK
[1,44] Written, Length: 182 bytes, Status: OK
[1,45] Written, Length: 182 bytes, Status: OK
[2,0] Written, Length: 2080 bytes, Status: OK
[4,3] Written, Length: 10 bytes, Status: OK
[4,4] Written, Length: 8 bytes, Status: OK
[4,9] Written, Length: 5 bytes, Status: OK
[8,0] Written, Length: 2 bytes, Status: OK
[8,3] Written, Length: 128 bytes, Status: OK
[8,4] Written, Length: 128 bytes, Status: OK
[8,8] Written, Length: 8 bytes, Status: OK
[8,10] Written, Length: 32 bytes, Status: OK
[11,0] Written, Length: 4 bytes, Status: OK
[11,1] Written, Length: 4 bytes, Status: OK
[11,2] Written, Length: 4 bytes, Status: OK
[11,3] Written, Length: 4 bytes, Status: OK
[11,4] Written, Length: 1058 bytes, Status: OK
[12,0] Written, Length: 102 bytes, Status: OK
[26,0] Written, Length: 16 bytes, Status: OK
[26,1] Written, Length: 68 bytes, Status: OK
[31,4] Written, Length: 14 bytes, Status: OK
[44,0] Written, Length: 1 bytes, Status: OK
[50,0] Written, Length: 2 bytes, Status: OK
[54,0] Written, Length: 2 bytes, Status: OK
[96,0] Written, Length: 2 bytes, Status: OK
[107,0] Written, Length: 41 bytes, Status: OK
[107,1] Written, Length: 89 bytes, Status: OK
[107,2] Written, Length: 89 bytes, Status: OK
[107,3] Written, Length: 70 bytes, Status: OK
[107,25] Written, Length: 236 bytes, Status: OK
[107,26] Written, Length: 12 bytes, Status: OK
[120,0] Written, Length: 944 bytes, Status: OK
[120,1] Written, Length: 160 bytes, Status: OK
[120,2] Written, Length: 130 bytes, Status: OK
[120,3] Written, Length: 112 bytes, Status: OK
[153,0] Written, Length: 68 bytes, Status: OK
[153,1] Written, Length: 68 bytes, Status: OK
[153,2] Written, Length: 68 bytes, Status: OK
[153,3] Written, Length: 68 bytes, Status: OK
[153,4] Written, Length: 68 bytes, Status: OK
[153,5] Written, Length: 68 bytes, Status: OK
[153,6] Written, Length: 68 bytes, Status: OK
[193,2] Written, Length: 8 bytes, Status: OK
[193,3] Written, Length: 32 bytes, Status: OK
[193,4] Written, Length: 32 bytes, Status: OK
[193,9] Written, Length: 64 bytes, Status: OK
[217,0] Written, Length: 32 bytes, Status: OK
[239,6] Written, Length: 218 bytes, Status: OK
[291,0] Written, Length: 92 bytes, Status: OK
[308,0] Written, Length: 1 bytes, Status: Not accepted, Code: 19
[308,1] Written, Length: 8192 bytes, Status: Not accepted, Code: 19
[308,2] Written, Length: 1 bytes, Status: Not accepted, Code: 19
[308,3] Written, Length: 1 bytes, Status: Not accepted, Code: 19
[308,4] Written, Length: 1 bytes, Status: Not accepted, Code: 19
[308,6] Written, Length: 1 bytes, Status: Not accepted, Code: 19
[308,7] Written, Length: 1 bytes, Status: Not accepted, Code: 19
[308,9] Written, Length: 40 bytes, Status: Not accepted, Code: 19
[309,0] Written, Length: 4 bytes, Status: OK
[309,1] Written, Length: 2 bytes, Status: OK
[309,2] Written, Length: 12 bytes, Status: OK
[309,3] Written, Length: 36 bytes, Status: OK
[309,4] Written, Length: 12 bytes, Status: OK
[309,7] Written, Length: 12 bytes, Status: OK
[309,17] Written, Length: 12 bytes, Status: OK
[322,0] Written, Length: 1 bytes, Status: OK
[329,0] Written, Length: 8392 bytes, Status: OK
[334,0] Written, Length: 1 bytes, Status: OK
[341,0] Written, Length: 1 bytes, Status: OK
[354,0] Written, Length: 13 bytes, Status: OK
[356,0] Written, Length: 2 bytes, Status: OK
[360,0] Written, Length: 1 bytes, Status: OK
[360,1] Written, Length: 2 bytes, Status: OK
[369,0] Written, Length: 40 bytes, Status: OK
Write PM Finished, Record written OK: 90, Record written NOT OK: 8
Success!
Started Phone Security Analysis...
MCU Version	V ICPR82_11w16.3
MCU Date	19-05-11
Product		RM-530 (Nokia E72)
Manufacturer	(c) Nokia
IMEI		357895047389012
Mastercode	661353460
Reading Security Block...
Security block OK and saved to "RM-530_357895047389012_15042019_154405.SecurityBlock.PM"
Step 1 : Testing SIMLOCK
SIMLOCK SEFLTEST PASSED OK!
Step 2 : Testing SECURITY
SECURITY SEFLTEST PASSED OK!
Step 3 : Analyzing Security Block
"1260010CB9D70344B630E084C12C14C6403EC732.C000261F" Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking ECC KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking DIV KEYS...
DIV KEYS FOUND AND CHECKSUM OK! PASSED!
Analyze finished!
</code>